Aurora Homepage
Forum Home Forum Home > Aurora Sequencer Software > Aurora 1.0
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Channel issues

 Post Reply Post Reply Page  12>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
webbtech View Drop Down
Groupie
Groupie
Avatar

Joined: 22 Dec 2007
Location: Murray Utah
Online Status: Offline
Posts: 48
  Quote webbtech Quote  Post ReplyReply Direct Link To This Post Topic: Channel issues
    Posted: 26 Sep 2011 at 9:42pm
New DLS file sequenced. On two channels when played with solid on all the time, the light blinks and wont come on again until the next solid on, then just blinks again. Built a "test" sequence and it works fine. Even pulled the test channels over to new sequence..same problem.
Upgraded all Dlight software and Aurora software. Re installed everything. It just wont work on this sequence. Any thoughts? I am test other sequences to verify that its only one. So far.
Mark Webb
Back to Top
LightsOnLogan View Drop Down
Admin Group
Admin Group


Joined: 11 Oct 2007
Online Status: Offline
Posts: 3187
  Quote LightsOnLogan Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 9:03am
For the newer D-Light firmwares (1.19+ I believe) there is a byte which needs to be set with the D-Light Hardware Utility to make the controller Aurora compatible (D-Light can provide instructions for setting this if you haven't done it yet).  Have you done this?

Michael
Back to Top
webbtech View Drop Down
Groupie
Groupie
Avatar

Joined: 22 Dec 2007
Location: Murray Utah
Online Status: Offline
Posts: 48
  Quote webbtech Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 9:06am
No Michael I have not.  So there is a patch of some sort. I will check this out and advise. Do you know what they call this "byte"?
Mark Webb
Back to Top
LightChristmas View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 15 Oct 2007
Location: Equality, IL
Online Status: Offline
Posts: 993
  Quote LightChristmas Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 10:34am
Latest ACx16 firmware is Ver 1.20 which is a corrected ver 1.19.

This mess happened when LOR got a wild hair and changed their protocol a bit.

To get Aurora to work with v1.20, do the following per Darryl:

http://www.d-light.us/forum/viewtopic.php?f=13&t=2014

"*IF* you are using Aurora, go into the HWUtil's "Advanced" tab
Select EEPROM 40 and set to 1 (from 0).

This is a hack to work with Aurora and the protocol changes in 1.19/1.20. This firmware does provide the comm error protection for "lost" id and stuck channel errors."

Back to Top
webbtech View Drop Down
Groupie
Groupie
Avatar

Joined: 22 Dec 2007
Location: Murray Utah
Online Status: Offline
Posts: 48
  Quote webbtech Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 10:56am
Now, just has a question...does v1.20 really do me any good or should I go back to where I was?
Mark Webb
Back to Top
LightChristmas View Drop Down
Beta Testers
Beta Testers
Avatar

Joined: 15 Oct 2007
Location: Equality, IL
Online Status: Offline
Posts: 993
  Quote LightChristmas Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 4:42pm
Ran 1.20 all last season with no problems, so I'd suggest updating to avoid any surprises.

Back to Top
webbtech View Drop Down
Groupie
Groupie
Avatar

Joined: 22 Dec 2007
Location: Murray Utah
Online Status: Offline
Posts: 48
  Quote webbtech Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 7:19pm
Dang Am I missing something here...? Where is this advanced tab located?

Mark Webb
Back to Top
webbtech View Drop Down
Groupie
Groupie
Avatar

Joined: 22 Dec 2007
Location: Murray Utah
Online Status: Offline
Posts: 48
  Quote webbtech Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 7:25pm
I see the little triangles far right but nothing moves when I click them...
Mark Webb
Back to Top
Jonathan View Drop Down
Beta Testers
Beta Testers


Joined: 07 Sep 2008
Location: SoCal
Online Status: Offline
Posts: 1237
  Quote Jonathan Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 8:15pm
You have to run the HW Utility from a command prompt with "-advanced" at the end. 

Or you could just copy / paste this into your command prompt:

c:\progra~1\D-Ligh~1\hardwa~1\DLight~1.exe -advanced

For more info on this, you can find it on the D-Light forum under this thread
~Jonathan
Back to Top
webbtech View Drop Down
Groupie
Groupie
Avatar

Joined: 22 Dec 2007
Location: Murray Utah
Online Status: Offline
Posts: 48
  Quote webbtech Quote  Post ReplyReply Direct Link To This Post Posted: 27 Sep 2011 at 8:35pm
well I would like to say it worked but it didnt... says its not a valid command. Tried it several times. Same results.  I am not a dos guy at all...I did read the D-light thread and it mentioned opening utility, discover, make sure you have a solid light and click the triangles to the right....nothing doing....getting frustrated. I am sure they hid that advanced tab for people like me....

Mark Webb
Back to Top
 Post Reply Post Reply Page  12>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.391 seconds.