|
Error 1931 |
Post Reply |
Author | |
spongebob101234
Newbie Joined: 07 Sep 2008 Location: Smithfield VA Online Status: Offline Posts: 10 |
Quote Reply
Topic: Error 1931 Posted: 07 Sep 2008 at 3:45pm |
Didn't know if you could help me...
When i install Aurora v1.0 i get this error message " Error 1931. The Windows Installer service could not update the system file C:§WINDOWS§System32§scrrun.dll because the file is protected by Windows. You may need to update your operating system for this program to work correctly." below that it has Ok or Cancel if I press ok the installer continues and later says Aurora Sequencer has been successfully installed. Click "Close" to exit which I do The I click on Aurora Sequencer from my desktop and click Import File I click Light-O-Rama v1.x File then I select my file and click open then a new dialog box comes up with "Importing Sequence" and at the bottom it says "Converting Events" whish at this point it just simply freezes until i end its task through the task manager I also cannot create a sequence from scratch. I have rebooted many times and uninstalled and installed many times. the § is meant as a back slash i am running Windows XP 2.8 GHZ 1Gb ram |
|
LightChristmas
Beta Testers Joined: 15 Oct 2007 Location: Equality, IL Online Status: Offline Posts: 993 |
Quote Reply Posted: 07 Sep 2008 at 4:48pm |
Make certain that the offending file's archive bit has not been set to Read-Only. If so, untag the Read Only and try reinstalling. If an install errors out in such a manner, its a given that the programs will not work properly either.
|
|
spongebob101234
Newbie Joined: 07 Sep 2008 Location: Smithfield VA Online Status: Offline Posts: 10 |
Quote Reply Posted: 07 Sep 2008 at 6:08pm |
Thanks for the help... One more problem arose from the solution... I get the same error message and code but instead of scrrun.dll I get maxml3.dll
I did the same steps as listed above (unchecking the read-only) for the msxml3.dll and still same problem... any HELP?!?!?!?!?!?
Thanks Much - CLaughinghouse
|
|
spongebob101234
Newbie Joined: 07 Sep 2008 Location: Smithfield VA Online Status: Offline Posts: 10 |
Quote Reply Posted: 07 Sep 2008 at 6:10pm |
Update:
Currently running Windows Update... so got my fingers crossed!
|
|
spongebob101234
Newbie Joined: 07 Sep 2008 Location: Smithfield VA Online Status: Offline Posts: 10 |
Quote Reply Posted: 08 Sep 2008 at 4:54pm |
No luck still... any more ideas?
|
|
spongebob101234
Newbie Joined: 07 Sep 2008 Location: Smithfield VA Online Status: Offline Posts: 10 |
Quote Reply Posted: 08 Sep 2008 at 8:26pm |
Update:
upgraded to service pack 3 and installs correctly... but when trying to import LOR1 sequences it just freezes... and im not sure how to describe this further.
|
|
LightChristmas
Beta Testers Joined: 15 Oct 2007 Location: Equality, IL Online Status: Offline Posts: 993 |
Quote Reply Posted: 08 Sep 2008 at 8:48pm |
Have you tried importing under LOR2? If you try to import a LOR2 sequence using the LOR1 import, it will freeze as you're describing.
|
|
spongebob101234
Newbie Joined: 07 Sep 2008 Location: Smithfield VA Online Status: Offline Posts: 10 |
Quote Reply Posted: 08 Sep 2008 at 9:05pm |
kudos to LightChristmas! that seemed to work until it got around 75% done and then Aurora just crashes... i know the crash problem is in another forum... heading over there now...
|
|
Post Reply |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |