What... The... Frig??? Shimmer Ramps.
Printed From: Aurora
Category: Aurora Sequencer Software
Forum Name: Bug Reports
Forum Discription: This is the place to report bugs
URL: http://www.aurorashow.com/forum/forum_posts.asp?TID=954
Printed Date: 30 May 2024 at 12:07am
Software Version: Web Wiz Forums 9.06 - http://www.webwizforums.com
Topic: What... The... Frig??? Shimmer Ramps.
Posted By: Pony_God
Subject: What... The... Frig??? Shimmer Ramps.
Date Posted: 10 Dec 2009 at 7:53pm
|
Okay, I set some ramping shimers, then save, then close, then open the same file ans they are no onger shimers, they are now normal ramps!!!??? WEIRD!
I've done this at least a dozen times.
Anyone else every see this? ------------- Fine. You're so smart you rig up the lights. http://www.frappr.com/dlight - D-Light users Unite! 
|
Replies:
Posted By: LightChristmas
Date Posted: 10 Dec 2009 at 8:20pm
|
Yup... In this instance a 100%-0% shimmer ramp adjoining a 100% shimmer causes the 100% shimmer to change to solid 100%.  Haven't dumped it to lights to see if its just a graphic error, though.Seeing the same thing happen in 1.0.4x and 1.0.6x. ------------- http://www.aurorashow.com/"> 
|
Posted By: Pony_God
Date Posted: 10 Dec 2009 at 8:38pm
|
weird!
The channels were acting funny, I'll check to see if it's graphical or actual next time though. ------------- Fine. You're so smart you rig up the lights. http://www.frappr.com/dlight - D-Light users Unite!
|
Posted By: Pony_God
Date Posted: 10 Dec 2009 at 9:03pm
|
Well, my shimmers are a bit short to tell so it's not a problem. ------------- Fine. You're so smart you rig up the lights. http://www.frappr.com/dlight - D-Light users Unite!
|
Posted By: LightsOnLogan
Date Posted: 10 Dec 2009 at 10:20pm
|
Need to make sure... the channel is set to a device type that supports ramping shimmer, correct? Is this with LOR or D-Light hardware? ------------- http://www.aurorashow.com/"> 
|
Posted By: Pony_God
Date Posted: 10 Dec 2009 at 10:28pm
|
Oh, yea, sure.
We're all D-Light hardware around here. That controller has 1.16 F/W on it.
RS485 adapter V3.
Aurora 1.0.69
All new for this season.
It's just that when it's just doing tons of shimmer-ramps for over a minute, it's hard to follow where the UI shows the non-shimmer-ramp, and watch that closely. Since it's hard for me to se, I know that no one will see the difference if there is any. ------------- Fine. You're so smart you rig up the lights. http://www.frappr.com/dlight - D-Light users Unite!
|
Posted By: LightsOnLogan
Date Posted: 11 Dec 2009 at 8:46am
|
I'm just checking, because there are two device type options in channel properties. The first (e.g. ACx16) doesn't render shimmer ramps. The second (e.g. ACx16 v1.13+) does render the ramps. If you have the wrong version of hardware selected in channel properties, then the behavior you mention is normal. Here's why:
Under those circumstances, when the sequence is "compiled", all shimmer ramps will be susbstituted with something that the specified hardware will support (D-Light firmware prior to 1.13 did not support shimmer ramps). Compiling is a step in either saving the file, or previewing it via send to lights. The uncompiled data is not saved to the file. When you re-open the file, it is decompiled to editable form, including any substitutions that were done.
If you have the proper device type specified, then it is possible you have a bad install (your version of the AuroraData component could be one that predates shimmer ramp functionality even though your main program supports it) ------------- http://www.aurorashow.com/">
|
Posted By: LightsOnLogan
Date Posted: 11 Dec 2009 at 11:14am
|
Do these shimmer ramps have a duration less than 0.17 seconds? ------------- http://www.aurorashow.com/">
|
Posted By: Pony_God
Date Posted: 11 Dec 2009 at 1:02pm
|
almost .3
http://www.nabor.com/2009%20-%20Trans-Siberian%20Orchestra%20-%20Jingle%20Bells.dls - http://www.nabor.com/2009%20-%20Trans-Siberian%20Orchestra%20-%20Jingle%20Bells.dls ------------- Fine. You're so smart you rig up the lights. http://www.frappr.com/dlight - D-Light users Unite!
|